Binance app

List of contents of this article:

• 1, What is the accurate installation method of automobile led bulb
• 2、Installation of car led lights
• 3,Binance app How to install car led lights

What is the accurate installation method of car led bulb

" provides you with the following relevant content: carInstallation method of led bulb: remove the original headlight, replace it with a hernia bulb of the same model, and install a stabilizer.

LED car headlights are installed in the light groove of the low beam headlights. The installation method is as follows: eject the spring card position. Take out the original car light bulb. Take out the lamp cuck. Fix the chuck with a spring. Connect the plug. Open the woven bag and put it in as shown in the picture.

Car led headlight installation tutorial steps: show the width light car led headlight installation tutorial knock out a concave hole on the surface with a small screwdriver, and repeatedly rotate to drill down. If there is an electric drill, it will be more trouble-free. Measure the circumference of the LED, choose a suitable drill, and dig a hole in three or two times.

Don't install some electrical appliances casually when you use the car. Many low-configuration models do not have LED. Most low-configuration models use halogen bulbs.Then some riders who buy low-configuration models want to install LED lights for their cars. Led is the abbreviation of light-emitting diode, which can directly convert electrical energy into light energy.

Because the bulbs of LED headlights glow on both sides, this installation method mainly takes into account that the lights, the left and right fan shapes are as scattered as possible, and the irradiation area is wider. So the industry standard is such an installation method.

The best installation angle of the car LED bulb: keep the left and right level of the led bulb during installation, fine-tune the direction after installation, and balance the beam level. When the adjusted beam level is uneven, manual fine-tuning is required. LED only takes tens of nanoseconds to improve driving safety.

Installation of car LED lights

Installation of LED lights: Install the LED lights in the original lamp position, and pay attention to the installation method and position of the LED lights should be consistent with the original lamps. During installation, you need to pay attention to the wiring method and voltage of the LED lamp to avoid safety hazards.

Remove the original headlight, replace it with the same type of LED bulb, and install a stabilizer; lead the line out of the dust cover, that is, there will be pores, so you should also do a good job of sealing;Although the cost of increasing power or spotlights is relatively low, the effect is limited.

In this way, you can master the correct installation method of the car LED bulb: remove the original headlamp, replace the same model of hernia bulb, and install the ballast; pull the wire out of the dust cover, that is, there is a gap, so the seal is also very firm; increase electricity or ramp. This method is low-cost but has limited effect.

How to install car led lights

Preparation Before installing car LED lights, we need to prepare some tools, including wrenches, screwdrivers, electric drills, wires, etc. In addition, it is necessary to purchase a suitable LED light set to ensure that it is compatible with the vehicle's circuit.

Turn on the engine box of the vehicle and place the led light in the position of the original headlight.Tighten the safety screws of the LED lamp one by one. Connect the original headlights or LED lights to the vehicle power supply. You can use the connection cable of the original headlights or the wire on the led lights.

If you want to improve your life, you can turn off the lamp with a lamp sleeve. Just press the face before the lamp pole is installed on the air intake grille of the front bumper. Just tie the wire and seal it with hot melt glue and waterproof it. The wheel should have the part where the tires are lowered and the light rod is installed on the brake pads. It depends on what kind of car it is and the parts of the parts.

The specific operation steps are as follows: first, find the big light bulb of the car. Rotate the headlight holder counterclockwise to remove it. Take the big light bulb down from the lamp holder. Take out the LED headlight and connect the socket of the LED headlight to the headlight socket of the vehicle. Insert the LED headlight into the lamp holder.

Don't install some electrical appliances casually when you use the car. Many low-configuration models do not have LED. Most low-configuration models use halogen bulbs. Then some riders who buy low-configuration models want to install LED lights for their cars. Led is the abbreviation of light-emitting diode, which can directly convert electrical energy into light energy.